FireDAC supports wide range of programming tools. Architecture, See Also. Programming Tools. Update Pack 4, Hot Fix 1 is required. See Borland Delphi 5. Dec 19, 2003 - Delphi 7 Studio includes Borland Kylix 3 for Delphi. Be the first to know about the hottest apps with Download's Windows Apps newsletter. Download Borland Delphi 5 Completo Hot. 4/1/2017 0 Comments Secure Delphi Download Options. Turbo C++ 3.0 Turbo C++ is a free C++ compiler from Borland. Download Delphi 5 Enterprise torrent from software category on Isohunt. Hot Torrents; FAQ; Movies charts. Delphi 5 Enterprise Download from Software: 2 years. STEP ONE: Download from, which contains the files you will need to use in the following instructions. Unzip these files into the “c: reskit” folder. [Source: ] STEP TWO At an MS-DOS command prompt, type “c: reskit INSTSRV.EXE HamachiService c: reskit SRVANY.EXE” (without the quotes). You will see a message that the service was successfully added. Run Registry Editor and locate the “HKLM SYSTEM CurrentControlSet Services HamachiService” entry. Add a new KEY with the name “Parameters”. Select the new Parameters key, then add a new VALUE with the name “Application”. Modify the new Application value, and edit the STRING data with “c: Program Files Hamachi hamachi.exe -srvany” (without the quotes). If you installed Hamachi to another folder other than c: Program Files, you will need to adjust that line accordingly. Delphi Borland WikiClick OK and then exit the Registry Editor. [Source: ] STEP THREE Open the Services applet (via Control Panel / Administrative Tools) or by running ’services.msc”. Scroll down to “HamachiService” and double-click it. Make sure STARTUP TYPE is “Automatic” then click on the LOG ON tab. Under LOG ON AS, select “Local System Account” and make sure the “Allow service to interact with desktop” is CHECKED. Data envelopment analysis software. Click APPLY and OK to close the window. STEP FOUR (optional) If you would like the new HamachiService to use your existing Hamachi identity information open an MS-DOS command prompt. Type “reg copy “HKCU Software Applied Networking” “HKEY_USERS.DEFAULT Software Applied Networking” /s” (without the outer quotes). You will see a message that the operation was completed successfully. STEP FIVE Reboot the computer. (Do not close Hamachi, let Windows shut it down while it is still online. Hamachi remembers it’s previous state, so, if you reboot the machine while Hamachi is connected, the service will start with Hamachi connected.). START HAMACHI AS SYSTEM SERVICE Resource: Running Hamachi as a Windows service: I highly recommend running Hamachi as a Windows service. It takes a little more effort, but here's how you do it. You need two utilities - instsrv.exe and srvany.exe. Both can be found in the Windows Server Resource Kits. You can find the Windows 2003 Server Resource Kit. But it is rather large and won't install on Pre-XP Windows machines. So you might be better off doing a for a site like. Borland Delphi 5Once you have these utiltites, copy them into your Hamachi directory. (I'm going to assume that you used the default directory from here on out.) Go to Start - Run - and type cmd to open the Command Prompt Type these commands in order and hit enter after each: cd C: Program Files Hamachi instsrv AutoHamachi 'c: program files hamachi srvany.exe' This will add Hamachi as an available service in Windows. Edit the Registry: Then you need to edit the registry to run the service properly. Add one of the following entries according to your Windows version. For Windows 2000: ( - right-click, save, and run) HKLM SYSTEM CurrentControlSet Services AutoHamachi ParametersApplication = c: program files hamachi hamachi.exeAppDirectory = c: program files hamachi AppParameters = -srvany For Windows XP / 2003: ( - right-click, save, and run) HKLM SYSTEM CurrentControlSet Services AutoHamachi ParametersApplication = c: program files hamachi hamachi.exe -srvany ————————— UPDATE: With the new version 1.0.0.45 the above registry keys have an additional command to point the service to the correct profile. Instead of simply the -srvany you need to add a -config tag followed by the file path to it. By default the config file will have the path: C: Documents and Settings _your_user_name_ Application Data Hamachi So for the new version you will have a string like this: -srvany -config 'C: Documents and Settings Administrator Application Data Hamachi' Note: Don't forget the quotes around the file path and replace 'Administrator' with your username. With the later version you can now skip ahead to the 'Configure the service' section below. ————————— Next you need to copy the user profile data you created during the installation from the current Windows user to the default system user in the registry. This needs to be done so that when Hamachi runs as a service it will have access to the info needed be able to connect to the virtual network you created. F1 challenge 99 02 download. There is several ways to copy the necessary registry data from one area to another, but this is the only way that I have found that works on all versions of Windows. Go to Start - Run - and type regedit and click OK to open up the regsistry editor. Navigate to: HKEY_CURRENT_USER Software Applied Networking In the top menu go to File (or Registry in server version) - Export (or Export Registry File) Give the file a name and then save it. Open the file in a text editor like Notepad. You need to edit the file to replace the two instances of: HKEY_CURRENT_USER with HKEY_USERS.DEFAULT Save the changed file as a.reg file and double-click it to apply the data to the registry. This effectively copies the Hamachi user profile from the original location in the regsitry to HKEY_USERS.DEFAULT Note: The copying of this data can also be done at the command prompt using the reg.exe program's copy command, but it is not available on all versions of Windows. Borland Delphi 5 Completo HottestNext you need to make sure this registry key is set to the value 1 so that Hamachi automatically connects on startup: ( - right-click, save, and run) HKEY_USERS.DEFAULT Software Applied Networking HamachiAutoConnect = 1 Configure the service: Go to Start - Control Panel - Administrative Tools - Services Right Click AutoHamachi - click Properties Select 'Log On' tab - check 'Local System Account' and then under it check 'Allow service to interact with the desktop'. Go back to the 'General' tab and for Startup Type select 'Automatic'. Reboot the machine and Hamachi should automatically start and connect. You should then be able to start up Hamachi on the the other computers and verify their connectivity. To make it easier to access other computers on your network, add the 5.X.X.X IP addresses with their corresponding host names to the hosts files of all the PCs.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |